Intermittent irrigation means not supplying water continuously for long periods, but irrigating in a rhythm of “wet, absorb, then re-water”; alternate wetting and drying (AWD), common in rice paddies, is one example. How long to water and how long to pause is decided by soil moisture, the weather and what the crop needs.

Article Summary|Irrigation is not just a matter of turning the water on. On the farm, water management is often the most fundamental yet most easily underestimated management task. Water too little and crops may suffer water stress, stunted growth and impaired flowering and fruiting; water too much and you may cause poor soil aeration, root oxygen deprivation, nutrient leaching and increased disease risk, and even make crops appear water-stressed when in fact the roots are damaged and their water uptake has declined. As a result, modern agriculture is gradually shifting from "irrigating on a fixed schedule" and "watering by experience" toward smart irrigation management that pays more attention to soil moisture, weather conditions, crop growth stages and irrigation effectiveness.

Intermittent irrigation is a management approach that does not supply water continuously for a long time. Instead it uses a rhythm of "wet, absorb, then add water again," giving water time to soak into the soil and be absorbed by the root zone, and lowering the risk of over-irrigation and wasted water. In rice paddies, Alternate Wetting and Drying (AWD), commonly used internationally, is a typical intermittent irrigation method. In smart agriculture more broadly, though, intermittent irrigation is not limited to rice. It can extend to staged irrigation, pulse irrigation, condition-based irrigation, and automated irrigation control for orchards, greenhouses, leafy vegetables, flowers, nurseries, and other crops.

The point is not a fixed formula of "how long to pause, how long to water," but whether you can answer these questions: Does the soil really need water now? Has the water reached the crop's root zone? Does soil moisture rise effectively after irrigation? When should the next irrigation happen? This is where FarmerPack and the Smart Control Box come in. FarmerPack helps a farm build soil, weather, and environmental data. The Smart Control Box can control water pumps, valves, or other equipment according to set conditions, so irrigation runs automatically based on the data and the settings.

1. What Is Intermittent Irrigation?

Intermittent irrigation means that irrigation does not supply water continuously for long periods, but instead replenishes water in a staged, phased, periodic or conditional manner. Simply put, it does not deliver all the water at once, but gives the soil and crops time to absorb the water and then decides on the next irrigation based on on-site conditions.

Common intermittent irrigation concepts include:

  • Irrigate for a period first, letting water enter the soil.
  • Pause for a period, letting water infiltrate downward or be absorbed by the root zone.
  • Observe whether soil moisture recovers.
  • When moisture drops to the management threshold, carry out the next irrigation.
  • Adjust the irrigation rhythm according to weather, rainfall, crop growth stage and soil conditions.

Compared with fixed-schedule irrigation, intermittent irrigation places more emphasis on the "process of moisture change." It is not only concerned with whether watering happened today, but with how soil moisture changes before, during and after watering. This is why intermittent irrigation pairs well with Smart Agriculture, precision agriculture, soil sensors, microclimate stations and automated control equipment.

2. How Is Intermittent Irrigation Different from Traditional Irrigation?

Traditional Irrigation: The Focus Is on "Whether Watering Happened"

A common management approach in traditional irrigation is a fixed time, fixed frequency or judgment based on manual experience. For example: watering once every morning, irrigating every two days, watering when the soil surface looks dry, watering a bit more when it is hot, or replenishing water when the crop looks slightly wilted.

These methods are intuitive and match the experience many farmers have accumulated over the years. The problem, however, is that conditions on the farm differ every day:

  • The same 30 minutes of watering has a different effect on a sunny day than on a cloudy day.
  • The same amount of water is retained differently by sandy soil and clay soil.
  • In the same field, moisture changes differently in high ground and low-lying areas.
  • For the same crop, water needs differ between the seedling stage and the fruiting stage.

Relying only on a fixed schedule easily leads to the problem of "watering happened, but not necessarily just right."

Intermittent Irrigation: The Focus Is on "Whether Water Is Effectively Used"

Intermittent irrigation is concerned with whether the water actually enters the soil after irrigation, stays in the effective root zone, and is used by the crop. Its management logic is not to supply a large amount of water at once, but to turn irrigation into an observable, adjustable and traceable cycle. For example:

  • Irrigate for 10 minutes the first time.
  • Pause for 20 minutes to observe changes in soil moisture.
  • If moisture still has not reached the target, irrigate again.
  • If moisture has recovered to a reasonable range, stop irrigation.
  • Determine the next irrigation based on how quickly soil moisture declines afterward.

3. Why Do Farms Need Intermittent Irrigation?

Problem 1: Watering a Lot at Once Is Not Necessarily Better

Many people think it is safer to water more all at once, but on the farm, over-irrigation is not necessarily beneficial to crops. Too much water may cause root oxygen deprivation, poor soil aeration, nutrients being washed away, increased disease risk, waterlogging in low-lying areas, and higher water pump and electricity costs.

Especially in poorly drained soils, greenhouse environments, potted systems or high-value crop settings, over-irrigation can sometimes be harder to deal with than brief water shortage. Intermittent irrigation can reduce the stress caused by supplying a large amount of water at once, allowing water to enter the soil gradually and be absorbed by crops.

Problem 2: Soil Needs Time to Absorb Water

Different soils have different infiltration rates. Sandy soil drains quickly and water easily flows downward and is lost; clay soil infiltrates slowly, so the surface may already be waterlogged while the lower layers are not evenly moistened; organic matter content, soil structure, slope and compaction also affect water movement.

If the irrigation rate is faster than the soil can absorb, the water may run off the surface or collect in one spot and not actually reach the crop's root zone. Intermittent irrigation uses a rhythm of "irrigate, pause, irrigate again," giving the water more time to soak in and spread out and reducing the waste caused by irrigating all at once.

Problem 3: A Fixed Schedule Cannot Reflect Weather Changes

Crop water demand is affected by weather. Under high temperatures, low humidity, strong sunlight and strong wind, water is consumed more quickly; on cloudy days, rainy days, in low temperatures and high humidity, water is consumed more slowly; after continuous rainfall, the soil may temporarily not need irrigation; after brief heavy rain, although it may look like a lot of rain, the actual infiltration and root-zone moisture still need to be observed.

If the irrigation system runs only on a fixed schedule, it may still irrigate after rain, or fail to replenish enough water during hot, dry periods. When intermittent irrigation is combined with microclimate and soil data, the irrigation strategy can more closely reflect the true on-site conditions.

Problem 4: Manual On-Off Operation Makes Stable Record-Keeping Difficult

The problem with manual irrigation is not that people cannot water, but that keeping stable records over the long term is difficult. For example: What time was the water turned on today? How long did it run? Which zone was turned on? Did soil moisture recover after irrigation? Is the water pump operating normally? What was different about this irrigation compared with the last?

Without records, it is hard to compare and hard to improve.

4. How Is Intermittent Irrigation Related to AWD?

In rice management, intermittent irrigation is often discussed together with AWD, that is, Alternate Wetting and Drying.

AWD can be understood as a water management method in which paddy fields are no longer kept continuously flooded for long periods, but are re-irrigated once the field water level drops below a certain threshold. IRRI's (International Rice Research Institute) Rice Knowledge Bank explains that safe AWD uses a field water tube to observe the water level, and when the level drops to about 15 cm below the soil surface, it is time to irrigate again; AWD typically uses a buried perforated water tube to observe the water level below the soil surface as a basis for deciding when to irrigate, and can reduce irrigation water demand. The FAO (Food and Agriculture Organization of the United Nations) also describes AWD as a water-saving irrigation technique that can be used in lowland rice farming, in which irrigation is applied after an interval following the disappearance of ponded water in the field.

But there is one point to note in particular here:

AWD is a specific method within paddy rice field management; the intermittent irrigation discussed in this article is a broader smart irrigation concept.

  • For rice, the focus may be on field water level and alternate wetting and drying.
  • For orchards, the focus may be on soil moisture, root-zone depth and drip irrigation cycles.
  • For greenhouses, the focus may be on substrate water content, temperature and humidity, and irrigation frequency.
  • For leafy vegetables and flowers, the focus may be on avoiding drastic moisture fluctuations and disease from excess wetness.

Therefore, intermittent irrigation cannot apply a single formula. It must be adjusted according to the crop, soil, climate, irrigation equipment and management goals.

5. What Data Does Intermittent Irrigation Need?

Soil Moisture: The Core for Deciding When to Replenish Water

Soil moisture is one of the most important pieces of data for intermittent irrigation. Without soil moisture data, intermittent irrigation easily becomes just another fixed schedule, for example a fixed "on for 10 minutes, off for 20 minutes," without knowing whether this truly matches the soil and crop needs.

Soil moisture data can help answer: Is the soil now close to water shortage? Did moisture recover after irrigation? Is the rate of moisture decline speeding up? Are different areas unevenly wet and dry? Did the soil truly get replenished after rain? Has it been excessively wet for a long time?

But soil moisture should not be judged from a single number. The trend matters more. For example, if soil moisture in one area drops step by step from 40% to 32%, 28%, and 24%, water is continuing to be lost. If after irrigation it rises only from 24% to 26%, the irrigation time may be too short, the sensor may be in the wrong place, or the water may not be reaching the effective root zone. If moisture stays too high for a long time after irrigation, drainage may be poor or too much water may have been applied.

Microclimate Data: Judging the Rate of Water Consumption

Soil moisture tells us the current moisture state in the soil, while microclimate data helps determine the background conditions of water consumption. Common data includes air temperature, air humidity, sunlight, rainfall, wind speed and wind direction.

The same soil moisture can mean different things under different weather: under high temperatures, strong sunlight and low humidity, soil moisture may drop faster; after rain or in a high-humidity environment, irrigation demand may decrease; strong wind may increase evapotranspiration and may also affect sprinkler uniformity. If intermittent irrigation looks only at soil moisture, it easily overlooks weather conditions; combining it with microclimate data makes the judgment more complete.

Rainfall Data: Avoiding Irrigation by the Schedule After Rain

Rainfall data is very important for irrigation management, because "it rained" does not equal "the crop root zone has received enough water." Light rain may only moisten the surface layer; heavy rain may produce runoff; continuous rainfall may cause excessive wetness and drainage pressure; and if you still irrigate on the original schedule after rain, you may over-supply water. By judging rainfall together with soil moisture, managers can adjust the timing of the next irrigation on a more solid basis.

Equipment Status: Confirming Whether Pumps and Valves Actually Operate

If intermittent irrigation is to introduce automated control, you cannot look only at environmental data; you also need to know whether the equipment actually executed. For example: Did the water pump start? Did the valve open? Did the irrigation time match the setting? Did the equipment stop abnormally? Did soil moisture recover after irrigation? If the platform only issues commands without recording equipment status, managers may still mistakenly assume irrigation has been completed on-site.

Crops and Management Zones: Avoiding One Condition Applied to the Entire Site

Intermittent irrigation should be adjusted according to crop and area. For example, the same farm may have different crops, different growth stages, different soil conditions or different irrigation zones. If all areas apply the same irrigation rhythm, it can hardly be called precision management.

Therefore, when adopting it, you should first confirm: how management zones are divided, which zones have drier soil, which zones are prone to waterlogging, which zones share the same set of valves, and which crops need different irrigation strategies. This data affects the placement of FarmerPack sensor points and also affects the control logic of the Smart Control Box.

6. How Does Intermittent Irrigation Work? Monitoring, Decision, Control, Feedback

Intermittent irrigation can be divided into four steps: monitoring, decision, control and feedback.

Step 1: Monitor Soil and Environmental Conditions

First, collect data through soil sensors and microclimate equipment, such as soil moisture, air temperature, air humidity, rainfall, sunlight, wind speed and equipment status. The purpose of this step is to establish a foundation of on-site data, not to irrigate automatically right away. Because without understanding the on-site moisture changes, it is hard to set reasonable irrigation rules.

Step 2: Set Irrigation Conditions and Thresholds

With data in hand, managers can begin to set initial irrigation conditions, for example:

  • Send an alert when soil moisture falls below a certain threshold.
  • Start irrigation when soil moisture falls below the threshold and there has been no recent rain.
  • Pause the irrigation schedule when rainfall reaches a certain level.
  • Send a drainage or stop-irrigation alert when soil moisture stays too high for a long time.
  • Prompt a check of the water pump or pipeline if moisture does not recover after irrigation.

Thresholds are not set once and left unchanged forever; they need to be adjusted according to the crop, growth stage, season and actual management experience.

Step 3: Start the Water Pump, Valve or Irrigation Equipment

When conditions are met, the system can execute equipment control through the Smart Control Box, for example: turn on the water pump for 10 minutes, open the valve for a designated zone, pause for 20 minutes to wait for water infiltration, re-check soil moisture, irrigate again if the target has not yet been reached, and stop irrigation if the target has been reached. Such control logic is closer to on-site needs than a simple timer, because it can adjust based on sensor data and management conditions.

Step 4: Observe Post-Irrigation Effects and Keep Optimizing

Every irrigation in intermittent irrigation leaves data behind. Managers can look at: how much moisture rises after irrigation, how long the moisture lasts, which area loses moisture faster, in what weather the irrigation interval should be shortened, which irrigation time setting works better, and whether there is an equipment fault or a clogged pipe. As this data accumulates, a farm can gradually build its own irrigation management rules.

7. What Benefits Can Intermittent Irrigation Bring?

Improving Water Management Precision

Intermittent irrigation judges irrigation needs from soil and environmental conditions rather than watering at fixed times, which helps reduce the risks caused by too much or too little water.

Reducing Unnecessary Irrigation

When the system knows the soil still holds moisture, or that recent rainfall has been enough, it can avoid unnecessary irrigation. Besides saving water, this also reduces pump running time, electricity use, and wear on equipment.

Reducing Root Stress and the Risk of Excess Wetness

For many crops, prolonged excess wetness may lead to root oxygen deprivation or an increased risk of disease. Intermittent irrigation can avoid keeping the soil excessively wet for a long time due to supplying a large amount of water at once, making water management more balanced.

Reducing the Burden of Manual Patrols and Manual Operation

After introducing monitoring and control, managers do not have to rely entirely on going to the site in person to check soil conditions, nor do they need to manually turn the water pump or valve on and off each time. This is especially helpful for settings with limited manpower, scattered farmland or a need for scheduled management.

Building Traceable Irrigation Records

When intermittent irrigation is paired with a platform, it can store irrigation times, equipment actions, soil moisture changes and environmental data. This data can be used for internal management, crop batch comparison, irrigation strategy adjustment, equipment maintenance decisions, and as supporting evidence for agricultural traceability or project documentation.

8. Five Common Mistakes When Adopting Intermittent Irrigation

Mistake 1: Treating Intermittent Irrigation as a Fixed On-Off Cycle

For example, a fixed pattern of "on for 10 minutes, off for 20 minutes, on again for 10 minutes." This is not necessarily wrong, but without soil data it is just another fixed schedule and may not match what the site needs. Intermittent irrigation should be adjusted according to soil moisture, rainfall, weather, and crop condition, not just apply fixed times.

Mistake 2: Installing Only the Control Box, Without Sensor Data

With only a Smart Control Box, you can indeed switch a water pump or valve on and off, but the system does not know whether the soil actually needs water, nor how well the irrigation worked. That is closer to remote control or timer control, not yet complete smart irrigation. So to do intermittent irrigation, we recommend pairing it with FarmerPack or soil and micro-weather sensing data, so the control logic has something to go on.

Mistake 3: Installing Only Sensors, Without an Execution Mechanism

Conversely, with only sensors, managers can see the data but still have to judge and switch equipment by hand each time. This is valuable for early monitoring, but to reduce the labor load you need to go further and link control equipment. A complete solution should therefore be "sensing data + platform judgment + equipment control."

Mistake 4: Ignoring the Conditions of Pumps, Pipelines and Valves

Intermittent irrigation is not only an issue of IoT equipment; you also need to check whether the on-site irrigation system itself is suitable for control. For example: whether the water pump has enough power, whether the pipeline zoning is clear, whether the valve can be electrically controlled, whether water pressure is stable, whether manual/automatic switching is needed, and whether there is protection against dry running, leakage or overload. If the on-site hydraulic equipment itself is not well organized, smart control can hardly take effect.

Mistake 5: Not Retaining Manual Intervention and Safety Mechanisms

There are many variables on the farm, and not everything can be entirely handed over to automation. When introducing control for intermittent irrigation, it is advisable to retain: manual on-off, abnormal shutdown, a maximum irrigation time limit, a rain stop-irrigation condition, equipment status reporting, operation records and permission management. This helps avoid erroneous irrigation caused by sensor anomalies, communication interruptions or equipment failures.

9. How Do FarmerPack + Smart Control Box Enable Intermittent Irrigation?

To make intermittent irrigation work, you need to connect "on-site sensing, data transmission, platform judgment, and equipment control" into one process, so FarmerPack should be paired with the Smart Control Box.

FarmerPack: Building the On-Site Data Needed for Irrigation Decisions

FarmerPack's role is to help farms establish a foundation of soil and environmental data, monitoring agricultural environment data such as soil moisture, soil temperature, air temperature, air humidity, rainfall, sunlight, wind speed and wind direction according to the needs of the site.

With this data, managers can know: whether the soil is too dry now, whether water really got into the soil after rain, the differences in dryness between areas, how fast moisture drops under high heat or strong sun, and whether soil moisture rises effectively after irrigation.

Smart Control Box: Letting Pumps and Valves Operate According to Conditions

The role of the Smart Control Box is to convert platform decisions into on-site equipment actions, and it can be used to control water pumps, solenoid valves, fans, motors, supplementary lighting equipment or other devices that can be controlled via I/O signals.

In intermittent irrigation applications, the Smart Control Box can execute according to set conditions:

  • Start irrigation when soil moisture falls below the threshold.
  • Automatically stop after irrigating for a set time.
  • Pause for a period to wait for water infiltration.
  • Then decide whether to irrigate again based on soil moisture.
  • Pause irrigation when rainfall meets the condition.
  • Send an alert when equipment is abnormal.

Cloud Platform and App: Turning Irrigation into Traceable Management Records

When FarmerPack and the Smart Control Box are used with a cloud platform, irrigation leaves a complete record. The platform lets managers check real-time soil moisture, environmental changes, rainfall records, equipment status, irrigation times, alert records, historical trends, and the effect before and after irrigation.

From Monitoring to Automated Control, Adopt in Stages

Not every farm needs fully automated irrigation from the start. It is advisable to adopt it in three stages:

  • Stage 1: FarmerPack establishes soil and microclimate monitoring.
  • Stage 2: The platform sets alerts and irrigation recommendations.
  • Stage 3: Pair with the Smart Control Box to link water pumps or valves and introduce intermittent irrigation control.

10. Which Settings Suit an Intermittent Irrigation Solution?

Open Farmland

Suitable for settings that need to grasp rainfall, soil moisture, crop water demand and the burden of manual field patrols.

Orchards

Suitable for settings that need to manage root-zone moisture over the long term, avoid drastic moisture fluctuations, build irrigation records and manage zones.

Greenhouses and Protected Agriculture

Suitable for high-value crop settings that need to control substrate moisture, ambient temperature and humidity, ventilation and irrigation rhythm.

Nurseries, Flowers and Leafy Vegetables

Suitable for settings that are sensitive to moisture changes, need a stable management frequency, and have a high manual watering burden.

Smart Agriculture Demonstration Sites and School Farms

Suitable for settings that need to demonstrate smart agriculture, precision irrigation, data recording, automated control and educational applications.

11. What Conditions Should You Confirm Before Adopting It?

First, Crop and Soil Conditions

Different crops and soils suit different irrigation strategies. Before adopting it, you should confirm the crop type, growth stage, root depth, and the soil's drainage and water-retention capacity.

Second, the Current State of Irrigation Equipment

You need to confirm whether the site already has water pumps, pipelines, valves and control panels, and whether they can be safely controlled by a Smart Control Box.

Third, Power and Communication Conditions

Farm settings often have power and network limitations. Before adopting it, you should confirm whether the site has mains power or a need for solar power, and the availability of communication options such as 4G, Wi-Fi, LoRa and NB-IoT.

Fourth, Sensor Points and Control Zoning

Sensor locations must be representative of the management area, and control zoning must also match the actual irrigation pipelines. Otherwise you may run into the problem of sensing Zone A but controlling Zone B.

Fifth, Management Rules and Safety Mechanisms

Before introducing automated control, you should set basic safety conditions, such as maximum irrigation time, rain stop-irrigation, manual intervention, equipment abnormality alerts and operation records.

Conclusion: Intermittent Irrigation Is Not Simply About Saving Water, but About Making Irrigation Evidence-Based

Intermittent irrigation is not just splitting the water into several rounds. The point is to let a farm decide, based on soil moisture, rainfall, weather conditions, crop needs, and equipment status, when to irrigate, for how long, whether to irrigate again, and whether the irrigation worked.

FarmerPack provides the on-site data foundation and helps a farm track changes in soil and micro-weather. The Smart Control Box turns data-based judgments into equipment actions, controlling water pumps, valves, or other irrigation equipment.

FAQ|Frequently Asked Questions About Intermittent Irrigation

Q1: What is intermittent irrigation?

Intermittent irrigation is a water management approach that divides irrigation into multiple, staged or conditional applications rather than supplying water continuously for long periods. It emphasizes giving the soil time to absorb water and adjusting the irrigation rhythm according to soil moisture, weather conditions and crop needs.

Q2: How is intermittent irrigation related to smart irrigation?

Intermittent irrigation is an irrigation strategy, while smart irrigation uses sensors, communications, platforms and control equipment to make the strategy monitorable, evaluable, executable and recordable. Combined, they move irrigation from manual scheduling toward data-driven control.

Q3: Is intermittent irrigation the same as AWD?

Not entirely. AWD usually refers to the alternate wetting and drying method used in paddy rice fields, where fields are re-irrigated after the water level drops below a certain threshold. The intermittent irrigation discussed in this article is a broader concept that can also be applied to orchards, greenhouses, leafy vegetables, flowers and other agricultural settings.

Q4: Does intermittent irrigation always save water?

Intermittent irrigation can reduce unnecessary irrigation, but the outcome depends on the crop, soil, climate, pipeline configuration, control logic and management approach. Without soil and weather data, simply running a fixed on-off cycle does not necessarily deliver good management results.

Q5: Can I do intermittent irrigation using only a timer?

You can achieve the most basic staged irrigation, but a timer cannot determine whether the soil is truly short of water, whether irrigation should stop after rain, or whether irrigation was effective. Therefore, for more precise intermittent irrigation, it is advisable to combine soil moisture, rainfall and microclimate data.

Q6: What role does FarmerPack play in intermittent irrigation?

FarmerPack helps collect on-site data such as soil moisture, ambient temperature and humidity, rainfall, sunlight and wind speed, allowing farms to see the moisture changes before and after irrigation as a basis for setting irrigation conditions and adjusting management strategies.

Q7: What role does the Smart Control Box play in intermittent irrigation?

The Smart Control Box can convert platform settings or sensor conditions into on-site equipment actions, such as controlling water pumps, valves or other equipment, so that irrigation can run automatically according to soil moisture, time schedules, rainfall conditions or safety rules.

Q8: What is the most important thing before adopting intermittent irrigation?

The most important step is to first confirm crop needs, soil conditions, the current state of irrigation equipment, sensor placement, control zoning, power and communication conditions, and safety mechanisms. Intermittent irrigation is not simply about installing equipment; it requires planning data, decision-making and control processes together.

References

  • IRRI Rice Knowledge Bank:Saving Water with Alternate Wetting and Drying(AWD)。
  • FAO:Rice farming — saving water through Alternate Wetting and Drying(AWD)method。